Miele GAS KM 81-2 Manual de usuario

Operating instructionsGas cooktopKM 81-2@]äöM.-Nr. 04 426 731RAPROVEDCANADIAN GAS ASSOCIATION

Warning and Safety instructionsWhen using a cooker hood overthe gas cooktop, ensure that anyburners in use are always covered witha pan. Otherwise fla

BurnerBefore using for the first time, takeheed of the “Warning and SafetyInstructions”.Burner controlThe inner and outer burner are bothcontrolled by

BurnerPress in the control knob and turncounter-clockwise to the high setting(largest flame symbol).When the flame ignites, keep the button pressed in

BurnerEnsure that there is a minimum dis-tance of 5/8" (15 mm) between thewok or the pan and the control panel.Never place a pan on the control p

Cleaning and careIn the event of a pan boiling over, cleanthe burner and the cooktop surface im-mediately, to prevent the boiled oversubstance from bu

Cleaning and careWok/pan support, trivetCaution: the wok/pan support andtrivet become hot in use.The wok/pan support and trivet can beremoved for clea

Problem solving guideRepairs to the gas and electricalcomponents of this appliance mustonly be carried out by a suitablyqualified person. Repairs by u

After Sales ServiceIn the event of any fault which you can-not correct yourself, or if the applianceis under guarantee/warranty, pleasecontact:Your Mi

]öElectrical connectionThe automatic ignition requires connec-tion to an a.c. single phase 120 V,60 Hz power supply. Fuse rating is15 A. Actual power

@äElectrical connectionElectrical connection AUSElectrical connection of the applianceshould be undertaken by a suitablycompetent person in strict acc

Description of the applianceKM 81-2Description of the appliance2

]ö Gas connectionThis appliance must be installedwith a separate shut-off valve and agas pressure regulator.Both shut-off valve and pressureregulator

]öGas connectionPressure regulatorA pressure regulator convertible to Naturaland LP Gas (Liquefied Petroleum) isincluded with the appliance.Conversion

@ä Gas connectionConnection to the gas supply, orconversion from use on one type ofgas to another should only beundertaken by an approved, who isrespo

Appliance dimensionsKM 81-2Dimensions in mm:Dimensions in inches:Appliance dimensions23

Appliance dimensionsGas connection CDN/USA:Gas connection AUS/NZ:Appliance dimensions24

]ö Instructions for building-inThere may be a wall at the rear and awall or tall units at one side. On theother side however, no unit or dividermust s

]ö Instructions for building-inPrepare the cooktop cut-out as illus-trated.Dimension “B” applies for a combina-tion of appliances and is given

]ö Instructions for building-inPlace the seal provided f under theedge of the cooktop.b Appliancec Tensioning screwd Clampe Countertopf SealTur

@ä Clearance above and around the applianceKM 93-2 (shown), KM 81-2 respectivelyShown area indicates protected surface, which may be ceramic tiles or

@ä Clearance above and around the appliancebRange hood, if fitted, or base of cupboardsc Not less than 600 mm (acc. to A.G.Aand Miele) from burner to

Description of the applianceKM 81-2b Trivetc Wok/pan supportd Small burner capeLarge burner capf Burner ringgLarge burner cap baseh Ignitori Cable for

@ä InstallationThis appliance shall be installed inaccordance with these instructions,local gas fitting regulations, munici-pal building codes, electr

Test the appliance and instruct theuser making sure that the User’sInstructions are left with the User.If any of the above procedures donot produce sa

@ä Instructions for building-inStick the seal provided f under theedge of the cooktop.b Appliancec Tensioning screwd Clampe Worktopf SealTurn the tens

]ö Conversion to alternative types of gasWhen converting to alternativetypes of gas (LP gas) or back toNatural gas, the main jet and thesmall jets of

]ö Conversion to alternative types of gasChanging the main jet, (does notapply to conversion to Natural Gas).Using a 10 and 13 mm wrench, loosenthe

]ö Conversion to alternative types of gasReplacing the small jet for the lowestflame settingRemove screw d from fitting cusing an 8 mm wrench and a

]ö Conversion to alternative types of gasImportant note: When reassembling, it is importantto ensure that the profile b of thecontrol panel grips th

@ä Conversion to alternative types of gasThe appliance is set up for natural gas(NG).When converting to alternative types ofgas, the components as lis

@ä Conversion to alternative types of gasChanging the main jet, (does notapply to conversion to Natural Gas).Using a 10 mm socket spanner, loosenthe

@ä Conversion to alternative types of gasReplacing the small jet for the lowestflame settingRemove screw d from fitting cusing an 8 mm spanner and a

ContentsDescription of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2For your safety . . . . . . .

@ä Conversion to alternative types of gasScrew the three screws into the bur-ner base using a suitable cross-slotted screwdriver.Put the large burne

41

42

43

Alteration rights reserved / 22 / 000 AUS, CDN, NZ, USA - 4897M.-Nr. 04 426 731 (KM 81-2)This paper consists of cellulose which has been bleached wit

For your safetyWARNING: If the information in this manual is not followedexactly, a fire or explosion mayresult causing property damage,personal injur

Help protect our environmentDisposal of packagingThe transport and protective packing ismostly manufactured from the followingre-usable materials:– Co

Warning and Safety InstructionsImportant safety instructionsWarning:When using your cooktop unit,follow basic safety precautionsincluding the followin

Warning and Safety InstructionsCheck that all the burners are cor-rectly assembled before ignitingthe gas, otherwise the ignition couldmalfunction.Ple

Warning and Safety InstructionsWhen cooking or boiling in largepots or pans, ensure that there is aminimum distance of 2" (50 mm) be-tween the po