Miele CS 1012 G Manual de instalación

Operating and installation instructionsGas hobsCS 1012CS 1034To avoid the risk of accidents ordamage to the appliance it isessential to read theseinst

Safety with children~This appliance is only intended foruse by adults who have read theseinstructions. This appliance is not a toy!To avoid the risk o

Technical safety~Before installation, check theappliance for visible signs of damage.Under no circumstances should youuse a damaged appliance. It coul

~During installation, maintenance andrepair work, the appliance must beconnected from the gas supply andmains electricity supply.~While the appliance

Correct use~The appliance gets hot when in useand remains hot for quite a while after ithas been switched off. Do not touch itwhilst it could still be

~Ensure that the flames from theburner do not spread out beyond thebase and up the sides of the pan.~Unless the pan manufacturer statesthat you can do

Disposal of the packingmaterialThe transport and protective packinghas been selected from materials whichare environmentally friendly fordisposal, and

Please stick the extra data plate for theappliance supplied with thisdocumentation in the space provided inthe "After sales service" section

Rapid ignition systemThe appliance is supplied with a rapidignition system with the followingfeatures:–Rapid ignition without pressing undholding the

Switching on^To ignite the burner press the controlknob down and turn it anti-clockwiseto the large flame symbol. The ignitorwill make a clicking soun

In-operation indicator andResidual heat indicatorWhen a gas burner is switched on, therelevant in-operation indicator lights up.Once it has reached a

D Das Gerät ist auch für den Gebrauch in anderen als auf dem Gerätangegebenen Bestimmungsländer zugelassen. Die landesspezifischeAusführung und die An

Burner Min. pan base diameterin cmNormal burner 10Large burner 12Extra large burner 14Max. diameter at top ofpan in cmNormal burner 22Large burner 24E

Thermo-electric ignitionThis appliance has a thermo-electricignition safety device. If the flame goesout, for example if food has boiled overor if the

General notes,Under no circumstances use asteam cleaning appliance to cleanthis appliance. The steam couldreach the electrical components andcause a s

Stainless steel surfacesClean stainless steel surfaces using anE-Cloth or with a solution of warm waterand a little washing-up liquid appliedwith a so

BurnerDo not clean any parts of the burnerin a dishwasher.The burner should be dismantled andthen cleaned by hand using a solutionof warm water and a

,Repairs to the gas and electricalcomponents of this appliance mustonly be carried out by a suitablyqualified and competent person toensure safety (Ga

... the gas flame suddenly looksdifferent.Check whether the burner componentsare assembled correctly... the gas flame goes out duringoperation.Check

Miele branded cleaning and conditioning products areavailable for your appliance.These can be ordered via the internet onwww.miele-shop.com or from th

This appliance must be installed andconnected to services inaccordance with local and nationalsafety and building regulations.Fit wall units and extra

Safety distance above the hobA minimum safety distance must bemaintained between this appliance andthe cooker hood above it. See thecooker hood manufa

Gas-heated appliancesSafety precautions to take if you smell gasß Turn off the gas emergency control valve immediately.This is usually located near th

Safety distances to the sides of thehobIdeally the hob should be installed withplenty of space on either side. Theremay be a wall at the rear and a ta

Safety distance when installing the appliance near a wall with additionalniche claddingA minimum safety distance must be maintained between the workto

CS 1012a Spring clampsb Frontc Building-in depthd Building-in depth for the mains connection box with mains connection cable,L = 2000 mme Building-in

CS 1034a Spring clampsb Frontc Building-in depthd Building-in depth for the mains connection box with mains connection cable,L = 2000 mme Building-in

^Make the worktop cut-out for one ormore appliances as applicable.Remember to maintain the minimumsafety distance from the back wall,as well as from a

When installing two or more appliances next to each other a spacer bar b mustbe used between each one.See “Fixing the spring clamps and spacer bars”.W

a Spring clampsb Spacer barsc Gap between spacer bar and worktopd Sealing stripThe illustration shows a worktop cut-out with spring clamps a and space

Wooden worktops^Position the spring clamps supplieda and spacer bars b on the topedge of the cut-out in the positionsmarked.^Secure the spring clamps

^Apply silicone to the side edges andthe lower edges of the springclamps a and the spacer bars b.^Then fill gap e between the spacerbars and the workt

Installing the appliance(s)^Feed the connection cable downthrough the cut-out.^Starting at the front, position theappliance in the worktop cut-out.^Us

Guide to the appliance ...6CS 1012 ...6CS 1034 ...

Do not use any sealant unlessexpressly instructed to do so. Thesealing strip under the edge of the toppart of the appliance provides asufficient seal

All electrical work should be carriedout by a suitably qualified andcompetent person, in strictaccordance with current local andnational safety regula

ImportantThe electrical safety of this appliancecan only be guaranteed whencontinuity is complete between it andan effective earthing system, whichcom

,Connection to the gas supply, orconversion from one type of gas toanother, should only be undertakenby an approved and registered gasinstaller in str

ConnectionThe gas connection must be installedso that connection can be made eitherfrom inside or outside the kitchen unit,and the isolating valve mus

,Connection to the gas supply, orconversion from one type of gas toanother, should only be undertakenby an approved and registered gasinstaller in str

CS 1034Nominal rating at high settingGas type kWNormalburnerNatural gas HLiquid gas1.601.60 / 116 g/hLargeburnerNatural gas HLiquid gas2.502.10 / 153

Changing the jetsDisconnect the gas hob from themains electricity supply. Turn off thegas supply.To change the main jets^ Remove the pan support, burn

Function testCheck all gas fittings for leaks.^Reassemble the appliance.^Check the burner flame by operatingthe burner.The flame must not go out on th

In the event of any faults which you cannot remedy yourself, or if the appliance isunder guarantee, please contact:–Your Miele dealer, or–the Miele Cu

Preparing the worktop...34Installation of several appliances...35Fitting th

50

51

Alteration rights reserved/ 1610M.-Nr. 07 172 910 / 11

CS 1012a Extra large burnerb Normal burnerc Pan supportd Symbols to indicate which gasburner the control is fore DisplayDisplayl In-operation indicato

CS 1034a Large burnerb Normal burnerc Extra large burnerd Normal burnere Pan supportsf Symbols to indicate which gasburner the control is forg Display

Burnern Burner capo Burner headp Ignition safety deviceq Ignitorr Burner baseGuide to the appliance8

This appliance complies with allrelevant local and national safetyrequirements. Improper use can,however, present a risk of bothpersonal injury and ma